Directories: The Modulepath (Default Config)
Included in Puppet Enterprise 3.7. A newer version is available; see the version menu above for details.
The Puppet master service and the Puppet apply command both load most of their content from modules. (See the page on module structure and behavior for more details.)
Puppet automatically loads modules from one or more directories. The list of directories Puppet will find modules in is called the modulepath.
The modulepath is a list of directories separated by the system path-separator character. On *nix systems this is the colon (
:, as seen above), and on Windows it is the semi-colon (
It is an ordered list, with earlier directories having priority over later ones. See “Loading Content from Modules” below.
Every directory in the modulepath should only contain valid Puppet modules.
For details about module contents and structure, see the documentation on modules.
By default, the modulepath will usually be something like:
<ACTIVE ENVIRONMENT'S MODULES DIRECTORY>:$confdir/modules:<SYSTEM MODULES DIRECTORY>
The location of the modulepath is configured differently, depending on whether directory environments are enabled:
|Configuration||Location of modulepath|
|Config file environments or no environments||Value of
|Directory environments||Value of
You can view the effective modulepath for any environment by specifying the environment when requesting the setting value:
$ sudo puppet config print modulepath --section master --environment test /etc/puppet/environments/test/modules:/etc/puppet/modules:/usr/share/puppet/modules
The Base Modulepath
The base modulepath is a list of global module directories for use with all directory environments. It also serves as the default value for the
modulepath setting, which is used when directory environments are disabled. It can be configured with the
basemodulepath setting, but its default value is probably suitable for you unless you’re doing something unusual.
The default value of the
basemodulepath setting depends on your OS and the distribution of Puppet in use. This table lists the default
Note that all default values include
$confdir/modules; see here for info about the confdir.
|OS and Distro||Default Base Modulepath|
|*nix (Puppet Enterprise)||
|*nix (open source)||
|Windows (PE and FOSS)||
Examples of Default Modulepaths
Default settings for a new installation of Puppet Enterprise 3.7 and higher:
Default settings for Puppet Enterprise 3.3 and lower or upgrades to Puppet Enterprise 3.7:
Open source Puppet, directory environments enabled with
environmentpath = $confdir/environments, active environment is
Configuring the Modulepath
- If you are not using environments, you can directly configure the modulepath with the
modulepathsetting. This should generally be set in the
[main]section of puppet.conf, so it can be used by all commands and services.
- If you are using directory environments, the first element of the modulepath will always be the active environment’s
modulesdirectory. However, you can configure global module directories with the
basemodulepathsetting (see above). This should generally be set in the
[main]section of puppet.conf.
- If you are using environment config sections, you can set
modulepathin each environment’s section of puppet.conf. If that setting is absent in a given environment, Puppet will fall back to the global value of the
- If you are using dynamic environments, you can set the
[main]and use the
$environmentvariable in some of the directory names.
Loading Content from Modules
Puppet will use modules from every directory in the modulepath.
Empty and Absent Directories
Directories in the modulepath may be empty, and may even be absent. In both cases, this is not an error; it just means no modules will be loaded from that directory.
If no modules are present across the entire modulepath, or if modules are present but none of them contains a
lib directory, then Puppet agent will log an error when attempting to sync plugins from the Puppet master. This error is benign and will not prevent the rest of the Puppet run.
Duplicate or Conflicting Modules and Content
If the modulepath contains multiple modules with the same name, Puppet will use the version from the directory that comes earliest in the modulepath. This allows directories earlier in the modulepath to override the later directories.
For most content, this earliest-module-wins behavior is on an all-or-nothing, per-module basis — all of the manifests, files, and templates in the winning version will be available for use, and *none of that content from any subsequent versions will be available. This behavior covers:
- Puppet code (from
- Files (from
- Templates (from
- External facts (from
- Ruby plugins synced to agent nodes (from
However, Puppet occasionally shows problematic behavior with Ruby plugins loaded directly from modules. This includes:
- Plugins used by the Puppet master (custom resource types, custom functions)
- Plugins used by Puppet apply
- Plugins that happen to be present in Puppet agent’s modulepath (which should generally be empty, but may not be when running Puppet agent on a node that is also a Puppet master server)
With these plugins, the earlier module still wins, but the plugins are handled on a per-file basis instead of per-module. This means that if a duplicate module in a later directory has additional plugin files that don’t exist in the winning module, those extra files will be loaded, and Puppet will use a mixture of files from the winning and duplicate modules.
The upshot is, if you do a major refactor of the Ruby plugins in some module and then maintain two versions of that module in your modulepath, it can sometimes result in weirdness.
This is essentially the same Ruby loading problem that environments have, as described elsewhere in this manual. It’s not intentional, but it’s not likely to get fixed soon, since it’s a byproduct of the way Ruby works and Puppet only has a limited amount of control over it.